nanoFLASH βファーム 1.5.126 [ビデオ撮影・編集]
nanoFLASH βファームウェア 1.5.126 が26日(日本時間だと27日なのかな)公開されていました。
1.5.73が流出(?)してから一気にバージョンが上がっていますが、何が変わったのでしょうか。
リリースノートを観てみましょう。
Beta Version 1.5.126 ( 26 – Mar - 09 ) -
o Added menu option Video->720p60 to 30, 720p50 to 25. Cuts the frame rate in half for incoming 720p60 or 720p50 signals. Useful, for example, with cameras with a 720p30 or 720p25 mode which then double the frame rate of the camera's SDI output. The nanoFlash bit rate in this mode is applied to the reduced frame rate. For example, @ 280 Mbit from a 720p50 source reduced to 720p25, the 280Mbit applies across 25 frames.
o Added menu option System->Trigger->Remote & Record, in which either the Remote Switch or the Record button can be used for triggering record.
o Added separate menu option System->Trigger-> “TC > Last TC” . In this mode, the nanoFlash will only trigger to record if the incoming timecode is greater than the ending timecode of the last recorded clip. This helps to minimize unexpected recordings, for example when inserting or removing media in the camera, or playing back video off of the camera's internal media. Be aware, however, that if the camera's timecode is re-set to a smaller value, the nanoFlash may not trigger from the timecode unless the nanoFlash is then turned off and back on.
o The menu option System->Trigger->Timecode can trigger at any time that the timecode is increasing, unlike the above mentioned “TC > Last TC” . This may create unexpected short recordings due to camera timecode behavior.
o Added menu option Audio->Audio Channels Monitoring, for monitoring specific channels on the headphones output. Choose between channels 1 and 2, 3 and 4, 5 and 6, or 7 and 8.
o Added clip skipping during playback, press up arrow during playback to move to next clip, press down arrow to move to previous clip. (A clip is a single record session, a clip may be composed of several files for a long record. )
o Fixed bugs in cranking, which extends compatibility of 720p24 / 25 / 30 at 50 Mbit and above to Sony Vegas, Edius, and Adobe Premiere CS3 / 4 (with Main Concept plug-in) in addition to the already supported Final Cut Pro. Other Pc-based NLE's may additionally support. 720P24/25/30 50 Mbit and above is not supported by Avid, however, at this time.
o Fixed slight pixelation in playback of Quicktime files from nanoFlash, a problem introduced in version 1.5.31 .
o Fixed staticky audio channel 1 in standard def MXF recordings, a problem introduced in version 1.5.31 .
o Fixed MPG reversed audio channels.
o Repaired 720p pulldown removal embedded timecode.
o Added support for true 30, 60 video formats in Quicktime (true 24 was already supported).
o MPG playback: pause is disabled, not supported by codec in MPG mode.
Known issues (1.5.126) :
o 720P24 / 25 / 30 playback from the nanoFlash is not supported at this time.
o Pulldown removal from JVC 700 requires turning the nanoFlash on 1st, then the camera, to work properly.
o Playback from nanoFlash (all MXF, QT files): 2 frames out of sync. Files are in sync when played on a computer.
o HDMI in / out: 2 channel audio support only. SDI in / out supports 0, 2, 4, or 8 channel audio.
ん～。
自分にはあまり関係ない内容が並んでいます。
1.5.31からの変更点とされている様なのですが、そのほとんどは1.5.73で挙げられていたもののようです。
720p関連の追加と、TCトリガーの設定が追加されています。
あとは、SDIの8ch audioのモニタリング設定と再生関連とバグ修正。
いつのまにか、1.5.126がカレントVersionのファームウェアになってます。
なかなかの完成度なので、音声問題などがある場合はアップデートしてみるとよいかと思います。
by すえぴ〜 (2010-04-12 22:06)